|
|
||||
| PiMPro Tower Series | PiMPro Tower 1821 | |||
Pattern Viewer |
|
Measurement & Configuration
 |
Main Screen Main boot-up screen shows all measurement features in graphic icon format. Selecting the appropriate icon opens the associated measurement screen. This screen also provides access to the complete system configuration, report management and access to an abbreviated user manual. |
|
 |
PIM & Return Loss PiMPro’s main measurement screen provides instantaneous PIM measurement in both dBc or dBm. The large display flashes to annunciate the presence of RF power at the output connector. Pass/Marginal/Fail Limits, Output Power, Frequency and IM settings originate from this screen. PiMPro’s unique Return Loss diagnostic feature at high transmit (TX) power, quickly points out open cables. |
|
 |
PIM vs Time Measurement The PIM vs Time dynamic measurement mode features a graphical representation of PIM as a function of time. Time scale can be set from 10 seconds to 4 minutes. The PiMPro Return Loss feature is also available on this screen. |
|
 |
Frequency Sweep PiMPro displays a swept receive (RX) PIM range by sweeping the TX carriers from end to end within the set frequency band. PIM frequency response is displayed, exposing the worst case PIM level and the contributing frequencies. Users can immediately transfer the graph to the PIM vs Time feature and run a new test to isolate the causes of the specific PIM. |
|
 |
DAS Measurement TX Function: Generates in the radio’s DL frequency a low power single tone anywhere within the DAS network (usually from the head-end) to evaluate RF connectivity and path losses. With three hours of TX time a technician can roam a DAS installation with a spectrum analyzer and detect systemic RF anomalies RX Function: Used as a receiver tool to evaluate ideal areas within a given location to position DAS antennas. Using a simple Yagi or planar antenna for external interference evaluation, a DAS antenna can be optimally positioned to locations where external interference is lowest. |
|
 |
Simultaneous DTF and PiMPoint Measurements After a simple calibration procedure, the unit allows simultaneous measurements (superimposed on the same screen) of Distance to Fault and PiMPoint (PIM vs. Distance). All the measurements are done from a single port, no need to disconnect to a separate measurement port. |
|
 |
Cable Insertion Loss Cable insertion loss measurements are accurately performed in the uplink of the PIM analyzers band. A simple open-short calibration is all that is required for this one port measurement. Much of the measurement error is removed with the displayed average insertion loss value. |
|
 |
Report Generator Report data for all measurement modes can be stored in either, HTML or PDF file format. Users can concatenate a limitless series of measurements with different sector, feeder, color codes, as one single PDF file. Reports can be saved in PiMPro’s internal memory or to external USB memory from the unit’s front panel. |
|
Accessories
| Included In: | |||||||
| Sys Pkg | Econ Pkg | PPT-AK | PPT-EAK | ||||
 |
 |
PP-AK-CBL-DMDM | Low PIM Male DIN to Male DIN jumper cable 3/8“ 3 m (10 ft) length | X | X | X | X |
| PP-AK-CBL-DMDF | Low PIM Male DIN to Female DIN jumper cable 3/8“ 3 m (10 ft) length | X | X | ||||
| PP-AK-PSTAN-80 | PIM Standard - 80 dBm | X | X | X | X | ||
| PP-AK-DMDM | Low PIM 7–16 DIN Male to Male Adapter | X | X | ||||
| PP-AK-DFDF | Low PIM 7–16 DIN Female to Female Adapter | X | X | ||||
| PP-AK-DMMF | Low PIM 7–16 DIN Male to 4.3-10 Female Adapter | X | X | ||||
| PP-AK-DMMM | Low PIM 7–16 DIN Male to 4.3-10 Male Adapter | X | X | ||||
| PPT-OS | Open - Short Standard | ||||||
| PP-AK-LOAD | Low PIM Termination Load < -168 dBc with both Male and Female 7–16 DIN | X | X | X | X | ||
 |
PP-AK-TORW | Torque Wrench for 7–16 DIN Connector | X | X | X | X | |
| PP-AK-ADJW | Adjustable Wrench | X | X | X | X | ||
 |
PP-AK-FIXW | Small 32 mm Wrench for 7–16 DIN | X | X | |||
| PPT-AK-BATT1 | Rechargeable Battery (28.8 VDC, 3450 mAh, 99.4 WH) | X | X | ||||
| PPT-AK-BATT | Rechargeable Battery (28.8 VDC, 4500 mAh, 130.0 WH) | ||||||
| PP-AKT-CHRGR | Battery Charger | X | X | ||||
| AKC | PiMPro Tower Accessory Kit Case | X | X | ||||
| PPT-TC | Tower Transport Case | X | X | ||||
| PPT-AC-ADPT | AC/DC Power supply | ||||||
| * All accessory kit components and cables have low PIM connectors, with PIM level <-122 dBm | |||||||
|
|
