14.5" (368 mm) OD Antenna Hoisting Harness

16.5" (419 mm) OD Antenna Hoisting Harness

Antenna Hoisting Hook for QPA65R-W3B

Antenna RET to RRU 20 in (0.5 meter) AISG Cable

Antenna RET to RRU AISG Cable

The Adjustable Mast Bracket (BSA-M05) can be used either in conjunction with the Mast Bracket Clamp (MBC-01) when a 2” to 5” diameter mast (pipe) is used, or on its own when Wall Mounting is desired.

The Remote Electrical Tilt (RET) Actuator is part of Communication Component Inc.’s complete RET System.

The Internal Remote Electrical Tilt (iRET) Actuator is part of Communication Component Inc.’s complete RET System.

Communication Components, Inc. (CCI) Bias-T’s are designed to combine the DC Bias and AISG compliant communication link provided by the “Site Control Unit” (SCU) with the RF signal from other equipment onto the center conductor of the feeder line.

Communication Components, Inc. (CCI) Bias-T’s are designed to combine the DC Bias provided by a Power Distribution Unit for TMA’s (PDU) or other DC Voltage source and the RF signal from other equipment onto the center conductor of a feeder line.

Communication Components, Inc. (CCI) Bias-T’s are designed to combine the DC Bias and AISG compliant communication link provided by the “Site Control Unit” (SCU) with the RF signal from other equipment onto the center conductor of the feeder line.

• Integrated AISG modem for combining or breaking out DC/AISG and RF frequencies covering 614-2700 MHz
• Compact weatherproof housing rated at IP67 available with optional 7-16, 4.3-10 or N-type connectors
• High power 300 W per port with low insertion loss in a small, lightweight enclosure
• AISG 2.0/1.1 Compliant with integrated lightning protection

4.3-10 Connector Protective Plastic Cap

Two RET Antenna with large RET spacing to RRU AISG Cable Kit.

Two RET Antenna with large RET spacing to RRU AISG Cable Kit.

Two RET Antenna with large RET spacing to RRU AISG Cable Kit.

Three RET Antenna with large RET spacing to RRU AISG Cable Kit.

Two RET Antenna with large RET spacing to RRU Right Angle AISG Cable Kit.

Two RET Antenna with large RET spacing to RRU Right Angle AISG Cable Kit.

Three RET Antenna with large RET spacing to RRU Right Angle AISG Cable Kit.

Three RET Antenna with large RET spacing to RRU Right Angle AISG Cable Kit.

Two RET Antenna with large RET spacing to RRU Right Angle AISG Cable Kit.

Remote Radio Interface

Unique bracket system, DM-01, allows for two four foot antennas to be mounted and installed in “side by side” configuration on a single pipe mast.

Unique bracket system, DM-02, allows for two antennas to be mounted and installed in “side by side” configuration on a single pipe mast.

Three RET Antenna to RRU AISG Cable Kit

Three RET Antenna to RRU Right Angle AISG Cable Kit.

HexPort Antenna to RRU AISG Cable Kit

HexPort Antenna to RRU Right Angle AISG Cable Kit

• Corrugated 0.195" low PIM jumpers
• 100% tested for PIM, return loss and insertion loss
• Ultra low PIM performance less than -160 dBc

• Flexible 1/2" low PIM jumpers
• 100% tested for PIM, return loss and insertion loss
• Ultra low PIM performance less than -160 dBc

Four RET Antenna to RRU AISG Cable Kit

Four RET Antenna to RRU Right Angle AISG Cable Kit.

This antenna mast bracket clamp is designed to convert CCI's BSA-M05 from a wall mount to a pole mount.

This antenna mast bracket clamp is designed for use with CCI's Small Cell Omni antennas.

This antenna mast bracket clamp is designed for use with CCI's Cardioid Small Cell Antenna.

This antenna mounting bracket is specifically designed for mounting our Small Cell Omni antennas to the top of utility and street lighting poles with a diameter of 4” (10 cm) and greater.

This antenna mounting bracket is specifically designed for mounting our BRS Omni antennas to the top of utility and street lighting poles with a diameter of 4” (10 cm) and greater.

This antenna mounting bracket is specifically designed to convert our MBK-08 and MBK-14 mounting kits from wall mount to pole mount with a diameter between 2 and 4.5" (5 - 11 cm).

This antenna mast bracket clamp is designed for use with CCI's Quasi-Omni Small Cell Antenna.

This antenna mast bracket clamp is designed for CCI's SCA360F-KW10A Omni antenna for pole mounting.

This two part antenna mounting bracket is designed for use with many of CCI's taller antennas, 5ft (1.5m) or longer.

This two part antenna mounting bracket is designed for use with many of CCI's 4 – 5 ft tall (1.2m – 1.5m) antennas.

This two part antenna mounting bracket is designed for use with many of CCI's 2 – 3.5 ft tall (0.6 – 1m) antennas.

This antenna mounting bracket is designed for mounting our Small Cell single sector antennas to metal or wooden poles up to 10 in (25 cm) or greater.

This antenna mounting bracket is specifically designed for mounting CCI's IDA-65F-KE-H1 Small Cell antennas to suitable flat surfaces.

This antenna mounting bracket is specifically designed for mounting CCI's IDA-65F-KE-H1 antenna directly to a wall.

This two part antenna mounting bracket is designed for use with many of CCI's larger antennas with a 600 mm hinge pitch.

This Dual Axis Tilt Antenna Mounting Bracket is designed for use with specific CCI small panel antennas, to attach to a suitable flat surface.

This two part antenna mounting bracket is designed for use with many of CCI's 4 – 5 ft tall (1.2m – 1.5m) antennas when no mechanical tilt is required.