Bi-Sector™ Array Antennas

CCI Portal Login

CCI Customer Portal

In the Americas
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
89 Leuning Street  
South Hackensack, NJ 07606  
Customer Service  
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
89 Leuning Street  
South Hackensack, NJ 07606  
Technical Support  
+1 (201) 342-3338 phone  
+1 (201)-342-3339 fax  
89 Leuning Street  
South Hackensack, NJ 07606  
      2.3 GHz Bi-SectorTM Array BSA-AA65-20R010-32
  • Three and a half foot (1.0 m), eight port, dual beam antenna with patented asymmetrical beam shapes optimized for LTE
  • Two 4x4 MIMO independent 33° beams to match existing 65° patterns, covering 2300-2400 MHz
  • Two pairs of +45° and –45° cross-polarized ports for each beam
  • Enhanced array spacing ensures maximum 4x4 MIMO performance
  • Slim and low weight single panel design supporting two beams in a single antenna
  • Field replaceable, integrated AISG 2.0 compliant Remote Electrical Tilt (RET) system with independent tilt control for each beam
  • Boosts data throughput by minimizing interference and optimizing coverage
  • Sharp elevation beamwidth aides in network planning
  • Optimal elevation sidelobe performance
  • Exceeds minimum PIM performance requirements



The CCI 2.3 GHz Bi-SectorTM array is a dual beam antenna with full 2.3 GHz band coverage. With four pairs of wideband ports covering 2300-2400 MHz, this three and a half foot (1.0 m) CCI Bi-SectorTM provides the capability to deploy two sectors of 4×4 Multiple-input Multiple-output (MIMO) in the 2.3 GHz band. On this Remote Electrical Tilt (RET) antenna all Left beams are linked and controlled with one RET motor and all Right beam are linked and controlled by a second RET motor, enabling maximum flexibility in network deployment.

CCI's unique patented bi-sector technology provides optimized overlap between the pairs of asymmetric beams, lowers soft handover losses in LTE, UMTS/HSPA+ and CDMA/EVDO systems, while minimizing interference between sectors. Fast roll-off of each of the outer beams and high front-to-back ratios ensure reduced interference. This patented approach enhances data transfer rates within LTE, UMTS and EVDO network sectors and addresses “hotspots” in mobile wireless operator networks.

The single panel design of the Bi-SectorTM Array offers the opportunity to reduce antenna count and directly replaces an existing 65° antenna without mount changes and avoids costly leasing and zoning changes. The enhanced coverage matches the existing sector footprint and minimizes the need for optimization and adjacent site changes, providing operators with significant CAPEX and OPEX cost savings.

CCI antennas are designed and produced to ISO 9001 certification standards for reliability and quality in our state-of-the-art manufacturing facilities.


  • Delivers increased capacity and data-throughput for sites that are performance or capacity constrained
  • Provides a higher level of spectrum reuse making it an ideal solution for spectrum limited markets
  • Increase capacity without the need for new site builds or carrier adds and without using valuable spectrum resources
  • Efficient use of spectrum make it ideally suited for spectrum clearing and refarming
  • Two sectors of 4×4 MIMO on the 2.3 GHz band


Ports 8 ×  Ports for 2300-2400 MHz
Frequency Range 2300-2400 MHz
Gain 20.0 dBi
Azimuth Beamwidth (-3dB) 28.5°
Azimuth Beam Cross-over -13.5 dB
Elevation Beamwidth (-3dB) 7.1°
Electrical Downtilt 0° to 10°
Elevation Sidelobes (1st Upper) < -17 dB
Front-to-Back Ratio > 30 dB
Cross-Polar Port-to-Port Isolation > 25 dB
Nullfill > -18 dB
Voltage Standing Wave Ratio (VSWR) < 1.4:1
Passive Intermodulation (2×20W) ≤ -150 dBc
Input Power Continuous Wave (CW) 300 watts
Polarization Dual Lineal 45°
Input Impedance 50 ohms
Lightning Protection DC Ground


Dimensions (L×W×D) 39.8×24.1×6.5 in (1012×613×165 mm)
Survival Wind Speed > 125 mph (> 201 kph)
Front Wind Load 205 lbs (912 N) @ 100 mph (161 kph)
Side Wind Load 63 lbs (279 N) @ 100 mph (161 kph)
Equivalent Flat Plate Area 8.0 ft2 (0.7 m2)
Weight* 52.9 lbs (24.0 kg)
RET System Weight 3.3 lbs (1.5 kg)
Connector 8 × 7-16 DIN female long neck
Mounting Pole 2 to 5 in (5 to 12 cm)
* Weight excludes mounting and RET
Bottom View  
Connector Spacing  
   PI BSAAA65 Connector Spacing
Element and RET Configuration  

Typical Antenna Patterns

  For detailed information on additional antenna patterns, contact customer support at
  BSAAA6520R01032 AP AZ2350 BSAAA6520R01032 AP AZ2350 EL5
  2350 MHz Azimuth 2350 MHz Elevation 5°
MBK-02   MBK-02 Mounting Kit
BSA-RET200   Remote Electrical Tilt System (RET)
CBK-AG-RRU-001   AISG Cable set for Two RET antenna
CBK-RA-AG-RRU-005   AISG Right Angle Cable set for Two RET Antenna
CBK-AG-RRU-003   AISG Cable set for Two RET antenna with single long RRU (5m) Cable
SCU-AISG-P   Portable AISG 2.0 Site Control Unit

Configuration File

Configuration FileVersion
Configuration FileVersion


pdficon large HPA-Firmware Upgrade Instructions
 softwareicon Current Firmware

Parts & Accessories

BSA-AA65-20R010-32-K Four foot (1.0 m) Bi-SectorTM Array 2300/2400 MHz with 7-16 DIN connectors, 2 factory installed BSA-RET200 RET actuators and MBK-02 mounting bracket
MBK-02 Mounting bracket kit (top and bottom) with 0° to 10° mechanical tilt adjustment
BSA-RET200 Remote electrical tilt actuator
CBK-AG-RRU-001 Two RET antenna to RRU AISG cable kit
CBK-RA-AG-RRU-005 Two RET antenna to RRU AISG right angle cable kit
CBK-AG-RRU-003 Two RET antenna to RRU AISG cable kit with single long RRU (5m) Cable

Standards & Compliance

Safety EN 60950-1, UL 60950-1
Emission EN 55022
Immunity EN 55024
Environmental IEC 60068-2-1, IEC 60068-2-2, IEC 60068-2-5, IEC 60068-2-6, IEC-60068-2-11, IEC 60068-2-14, IEC 60068-2-18, IEC 60068-2-27, IEC 60068-2-29, IEC 60068-02-30, IEC 60068-2-52, IEC 60068-2-64, GR-63-CORE 4.3.1, EN 60529, IP 24


Antenna Interface Standards Group (AISG), Federal Communication Commission (FCC) Part 15 Class B, CE, CSA US, ISO 9001
ISO9001Logo RoHS CE logo AISGLogo 3GPPLogo


89 Leuning Street

South Hackensack, NJ 07606

+1 (201) 342-3338

+1 (201) 342-3339 fax